Mustang Survival IPFD Recall

We have been users of the Mustang Inflatable Vests for many years and have been very satisfied with them. But we have recently been made aware of a recall due to a problem that might keep them from fully inflating. Here is the official recall notice...


November 2, 2011

MUSTANG SURVIVAL ISSUES VOLUNTARY RECALL NOTICE ON MD2010 & MD2012 model 22LB Inflatable Personal Flotation Devices

In keeping with Mustang Survival’s commitment to the highest levels of product quality and safety, we are voluntarily recalling all model number MD2010 and MD2012 inflatable Personal Flotation Devices (PFD’s) sold in the United States during 2011. To determine if you are impacted by this recall please reference the images below:
Image 1: Any inflatable product with multiple white sewn on safety labels on the back is OK and is not affected by this recall.





Image 2 If your inflatable does not have white sewn on safety labels, please check for model number MD2010 or MD2012 on the back of the PFD, then refer to Image 3.











Image 3 MD2010/MD2012 models with an “MIT” (Membrane Inflatable Technology) stamp (in black or color) above the CO2 cylinder are OK. Any MD2010 or MD2012 missing the “MIT” stamp should be returned to Mustang!
This recall is being issued for the inspection and repair of an inflator installation inconsistency that may prevent some units from fully inflating.  Mustang Survival has developed a solution that corrects any affected product and prevents re-occurrence of this issue.  The inspection and repair can only be performed at a Mustang Survival factory.
This recall notification is for only the MD2010 and MD2012 22LB buoyancy inflatable PFDs.  No other Mustang Survival products are affected as they utilize different inflator mechanisms. 
All MD2010 and MD2012 PFD’s without the stamped MIT logo as shown in Image 3 (above) should be returned to Mustang Survival for inspection.  All other Mustang PFD’s are okay for use.
Distributors and consumers are urged to contact Mustang Survival’s Customer Service department at 1-800-526-0532 between 7:30am and 4:30pm PST, Monday through Friday for specific shipping instructions.  If you have questions, please first refer to the Frequently Asked Questions below:

FREQUENTLY ASKED QUESTIONS
Q: Why do I have to return the product?
A: Our QA team has discovered an installation inconsistency with the inflator system that needs to be tested and corrected if necessary.
Q: How do I know if my inflatable is one of the affected products?
A: The model number is screen printed onto the back panel above the UL mark and will begin with the characters MD followed by four numbers. Affected products are MD2010 and MD2012
Q: When will I get my product back?
A: We are striving to have all products returned to dealers and consumers within 3-4 weeks (including shipping time to and from Mustang).
Q: What are you doing with my returned product?
A: All units will be tested and if necessary, repaired, before being returned. We will stamp the inside of the product above the CO2 cylinder with “MIT” to indicate that it has been tested and is OK.
Q: Are the re-arm kits affected by this recall?
A: Re-arm kits are not affected by this recall. The problem is isolated to the inflator assembly on the inflatable PFD.
Q: Is this a problem caused by the M.I.T. (Membrane) technology?
A: No, the problem is with the inflator installation on the affected units.
Q: Does this recall impact any other Mustang inflatable PFDs?
A: No, the recall is limited to only the MD2010 and MD2012 models due to its unique inflator components and installation method.
Q: How do I return my product?
A: Contact Mustang Survival’s Customer Service department at 1-800-526-0532 between 7:30am and 4:30pm PST, Monday through Friday with any questions or concerns regarding this voluntary recall notice.
Q: What are the shipping and repair costs?
A: Mustang Survival will pay for all testing, repair and shipping costs.
Q: How are you notifying the public about this issue?
A: A detailed communications plan is being executed to notify all affected dealers, distributors, consumers and industry partners.

Moeller Marine Products Review

Over the years we have often used Moeller Marine products, also sold under Tempo, and found them to be of fairly decent quality. But our most recent purchases have changed our opinion considerably. Here on the Beach House site we often post the specific product we are working with and links to where it can be found. When we use a product we like, it gets a good mention and we will often recommend it to others. But when we find a product we consider of poor quality we feel just as obligated to let others know of our experience. Three recent products made by Moeller have made our "Never Again" list. 

Each of these was purchased only a few months ago and only used a couple of times. The first is a pad that goes over the transom of our dinghy to cushion it when the outboard is mounted. This has only been used one other time with the outboard on and when we mounted the outboard again this weekend, here is the condition we found the pad to be in. It has split completely in half. The dinghy is mounted horizontally on our swim platform and it is impossible for anything to come in contact that might cause this problem.

The next is the premade fuel line that connects the outboard to the fuel tank. The squeeze bulb that lets you prime the line and the outboard is made of such a hard rubber material that you can't squeeze it to prime anything. You must virtually step on it to get the bulb to compress.

The hose itself is starting to collapse from the inside. We are always very careful not to crimp the hose but this one has already developed a crimp on its own, right at the end fitting. Also note the cheap crimped clamp on the end fitting since this too is a problem.

Both ends leak where the hose attaches to the end fitting connectors because the crimped clamp does not clamp down tight enough on the hose. You can easily spin the end connectors and if you can get enough pressure on the priming bulb the ends leak and will continue to leak when the engine is running and pulling fuel from the tank.

The biggest disappointment has been the brand new 3 gallon fuel tank that we purchased about a month ago. We use three gallon tanks for the dinghy so that the gas in the tanks get turned over quickly and we don't have to throw away bad gas, especially as expensive as it is now. The first time we filled up the tank and carried it down the dock we found it was leaking all over the place. Upon further inspection it was determined that the threads for the plastic cap that holds the pick up tube was split in half where the threads meet the mounting.

After disassembling the fitting, I used the handle for the pliers to hold open the split to show how bad it was. Note the other tank sitting next to the broken one. This older tank is a couple of years old and is also a Moeller tank. It has shown no signs of problems and continues to be leak free. I can only make the assumption that the manufacturing process has changed and quality control has gone down the tubes. The colors of the tanks are not the same further indicating to me that things have changed. Perhaps if it had been a single product we might have just taken it back for exchange. But three different products from the same manufacturer all failing in such a short period leads me to only one conclusion. We don't want this product on our boat. This time we will take the hit and reorder all three of these from another manufacturer. I invite Moeller to come on the site and comment on this if they care to.

Our Navigational Notices and Other Work Related Stuff

We haven't been totally neglecting Beach House, but W-O-R-K has been interfering with our boat work a little. Our new projects for Marinalife are coming along nicely. We have quite a few Navigational Notices and Alerts posted that cover the eastern U.S. coast from Maine to Florida and the Gulf Coast, Great Lakes and inland Waterways that include the Great Loop Route. We have even posted a few from the west coast, but not as extensive as the rest. We are also putting together cruising itineraries based on some of our previous cruises that include marina stops and anchorages for a leisure cruise south on the ICW, with stops at about every 50 miles. We will have another cruise template for the ICW from the Georgia border to the Florida Keys, but that will probably not be up for another week. If anyone wants to receive my Navigational Notices, you can go to the Marinalife website and register, and then sign up for whatever areas you want on your dashboard page. It is all free and I send out the Notices as soon as I receive and verify them. They can be read on the website or sent right to your email box. The notices are also linked to our Nautical Chartviewer so you can see the exact area where the notice is posted.

We have also done a few articles for Marinalife Magazine and Susan has an article that has just been picked up by Cruising World. We've compiled many of our anchorages and included them in the Marinalife Chartviewer, plus we have an article for anchorages along the ICW that we will be posting later. Keeping up with all of our other writing has kept us off the blog for a while, but we will make it up soon. Besides working to build the cruising Kitty, we are renovating the flybridge and will post on that as soon as we're a bit farther along. Our plan is to replace the old fiberglass seats, Awlgrip areas we have not done yet and redo the non-skid on the decks. It's still a work in progress, but we are moving along.

We are in our third marina since we arrived in south Florida. We have always wanted to be able to sample different locations rather than just park in one spot as we have often done. Being able to do this is not only fun, but it lets us feel more like we are still boating rather than just sitting and working. More on that later too. The big projects are yet to be done. The autopilot will be next after we finish the flybridge. After that, and a few smaller things, we will tackle the generator. So stick around and sign up for Marinalife updates through email or RSS feed, and we will keep on keepin' on.